Ventilation,indoor environment quality and climate—comparison of European and Singapore office buildings

Indoor environment quality audits were performed in six European countries and in Singapore using the same methodology. Five to eight office buildings were audited in each country. The audits included airflow rate measurements, energy audit, indoor air quality (VOC₁ CO₂, dust concentrations), and questionnaires to occupants. Questions to occupants addressed their health, their comfort and well-being, as well as their perception of their environment. This paper compares the results obtained from these audits, with particular attention to the effects of ventilation or air conditioning systems and climate.

The number of building related symptoms is, on the average, significantly smaller in the buildings audited in Singapore than in Europe. One of the reasons may be the non-smoking policy common in Singapore. It is also once more observed that buildings are often over-warmed in cold climates and overcooled in warm climates. Surprising, but not new, is that there are no correlations between specific air flow rates and perceived air quality or health, as long as airflow rates are within accepted standards.     

New correlations for estimation of monthly average daily solar radiation on a horizontal surface using meteorological data

This study deals with the estimation of monthly average daily global solar radiation incident on a horizontal surface at a location using meteorological data for different cities of Andhra Pradesh state. The regression equations of two types of models are developed for various locations of the state having varied climatic regions using measured meteorological parameters obtained from different measuring stations. Parameters such as the latitude and height of the location, maximum and minimum temperature and relative humidity are considered to develop linear and quadratic regression equations to estimate the monthly average daily global radiation. The estimated values are compared with measured data and with other theoretical models in terms of mean percent errors calculated using recognised statistical criteria of MBE, MABE, MPE and RMSE. The proposed quadratic model performs better than the proposed linear models and shows good agreement with the long-term pyranometer data of various locations with a deviation of less than 10%. In comparison with other theoretical models presented so far, the suggested models are expected to perform with a higher degree of accuracy.     

Quaternized poly(phenylene oxide) anion exchange membrane for alkaline direct methanol fuel cells in KOH‐free media

A series of anion exchange membrane (AEM) electrolytes with quaternary ammonium moiety are fabricated from poly (phenylene oxide) for its application in alkaline direct methanol fuel cells (ADMFCs). In the first step, poly(phenylene oxide) (PPO) is successfully chloromethylated by substituting chloromethyl groups in the aryl position of polymer. In the second step, the chloromethylated PPO (CPPO) is further homogeneously quaternized and ion‐exchanged to form an AEM. From the second step, series of AEMs are prepared by changing the mole ratio of amine in relation to CPPO. The presence of quaternary ammonium group in the membrane was confirmed by elemental analysis. The fabricated membranes are subjected to cell polarization studies in ADMFCs, wherein quaternized poly(2,6‐dimethyl‐1,4‐phenylene oxide) (CPPO:amine of 1:8) membrane exhibits higher peak power density of 3.5 mW cm^?2 when compared with the other ratios of CPPO:amine in the absence of KOH solution. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43693.     

Enhanced visible green and 1.5 μm radiative emission of Er~(3+) ions in Li_2O-PbO-Al_2O_3-B_2O_3 glasses for photonic applications

A series of Er~(3+) ions doped lithium lead alumino borate(LiPbAlB) glasses were synthesized via melt quench method and their structural,physical and optical properties were studied.Judd-Ofelt theory in correlation with the emission and absorption profiles was performed for the measurement of various radiative parameters for different transitions of Er~(3+) doped glasses.The as-prepared glasses show deep green(550 nm) as well as NIR(1532 nm) emission at 380 and 980 nm excitation wavelengths,respectively.The intensity of emission spectra increases with Er~(3+) ions concentration up to 1.5 mol% and beyond quenching is observed.The Dexter theory applied to the emission profiles reveals the interaction between Er~(3+)ions as dipole-dipole in nature.CIE color coordinates are found to fall in the green region of the visible spectrum.It is observed that 1.5 mol% of Er~(3+) ions concentration is optimum to exhibit the maximum quantum efficiency,branching ratios,gain bandwidth,emission cross-section,gain crosssection and aptly suitable for visible and NIR photonic applications.     

Life estimation of shafts using vibration based fatigue analysis

Many rotating machinery components fail due to fatigue when subjected to continuous fluctuating stresses. Hence, estimation of fatigue crack initiation life is essential to avoid catastrophic failure. Effective vibration based fatigue life analysis requires measurement of accurate time varying signal. In this study, experimentally observed fatigue lives of rotating shaft, for three different notch configurations, are compared with fatigue lives estimated using two approaches based on an acquired vibration signal. The first one is time domain approach (based on Rainflow cycle counting) while the second one is frequency domain approach (based on power spectral density moments). In the frequency domain approach, fatigue life is estimated using the narrow-band approximation and Dirlik’s empirical solution. The performance of two approaches in estimating fatigue life for the same signal length taken at different time intervals from the total signal acquired is also discussed. In addition, experimental uncertainty analysis is performed and discussed in this study. A good correlation is found between the estimated fatigue life using Dirlik’s rainflow range probability density function and experimental life. Therefore, this study concludes that the Dirlik’s approach can be considered as preferable method for estimating fatigue life of rotating shaft.     

Optimum short-time polynomial regression for signal analysis

Sādhanā - We propose a short-time polynomial regression (STPR) for time-varying signal analysis. The advantage of using polynomials is that the notion of a spectrum is not needed and the...     

Nafion and modified-Nafion membranes for polymer electrolyte fuel cells: An overview

Polymer electrolyte fuel cells (PEFCs) employ membrane electrolytes for proton transport during the cell reaction. The membrane forms a key component of the PEFC and its performance is controlled by several physical parameters, viz. water up-take, ion-exchange capacity, proton conductivity and humidity. The article presents an overview on Nafion membranes highlighting their merits and demerits with efforts on modified-Nafion membranes. Energy security refers to various security measures that a given nation, or the global community as a whole, must carryout to maintain an adequate energy supply     

Influence of thickness on nanomechanical behavior of Black Diamond™ low dielectric thin films for interconnect and packaging applications

In the present study, we have investigated the thickness dependence of mechanical properties of the Black Diamond? (SiOC:H, BD, Low-k) films, which are of great interest in current Cu/low-k Back End of the Line (BEOL) interconnect/packaging technologies. For this investigation the BD thin films of six different thicknesses 100, 300, 500, 700, 1,000 and 1,200 nm were deposited on the 8″ Si wafer by using plasma enhanced chemical vapor deposition (PECVD) technique. Nanoindentation and nanoscratch tests of the BD films were performed by using the Nano Indenter^® XP (MTS Corp. USA). In nanoindentation testing of the BD films, significant differences in the elastic modulus of the BD films were observed. In nanoscratch testing, it is found that the critical load (Lc) and scratch width increases as the thickness of the film increases. Cross-sectional analysis of residual nanoindentation impressions was carried out using atomic force microscopy (AFM) to study the deformation behavior. The nanoindentation and nanoscratch responses of the BD thin films of six different thicknesses are different and they are expected mainly due to the molecular reorganization in thin/ultra thin films.